ECT 246 Complete ilabs Week 1 To 7

ECT 246 Complete ilabs Week 1 To 7

 

ECT 246 Week 1 iLab Power Supplies

TCO #1:

Given an application requiring an AC to DC regulated power supply discuss the block diagram of the supply, and how its internal subsystems are related, using the appropriate data sheets, determine the device’s operating parameters, calculate, simulate and measure the power supply’s electrical parameters.

 

ECT 246 Week 2 iLab Transistor Circuits

Part A-Transistor Circuits

TCO #2:

Given an application requiring a single-stage common emitter BJT amplifier and a common source JFET amplifier with voltage-divider biasing use the device’s data sheet to establish the operating conditions calculate, simulate, and measure the input and output parameters.

 

ECT 246 Week 3 iLab Op-Amps

Part A-Op Amps

TCO #3:

Given an operational amplifier (op-amp) circuit schematic, calculate, simulate and measure the input and output voltages, impedance, and signal gain for a inverting, non-inverting, and voltage follower op-amp configurations.

A.Define the basic concepts of an op-amp including its symbol, input modes such as differential inputs, common mode rejection ratio, input and output impedance, slew rate and negative feedback.

B.Examine a common op-amp’s data sheet such as a LM741C to determine the device’s, electrical characteristics, and standard applications.

 

ECT 246 Week 4 iLab Audio Amplifiers

TCO #4:

Given an audio amplifier application that uses an integrated amplifier, examine the overall amplifier’s performance and verify the operation by using suitable input and output circuits.

 

ECT 246 Week 5 iLab Op-Amps

In week five, you will create several circuits using the operation amplifiers you studied earlier. An op-amp can be configured to perform special applications found in everyday electronic equipment. These include comparators, level detectors, summing amplifiers and digital to analog converters.

A.Describe the operation of a level detector.

a.Explain the operation of the following circuit.

B.Determine the output of a level detector for a given reference voltage. Simulate a level detector and verify that the simulated voltages agree with the calculated values.

C.Explain the operation of a summing amplifier and how the output voltage is calculated based on the input values.

E.Calculate the output voltage of a three input summing amplifier.

F.Simulate a summing amplifier with three inputs, measure the results and compare them to the calculated values.

 

ECT 246 Week 6 iLab Filters and Oscillators

Part A-Active Filters

Week six addresses the concept of active filters and oscillators. The low, high, bandpass and notch active filters, their circuits, and operating parameters are covered. The Wein-bridge RC oscillator, its configuration, operation and circuit is discussed.

TCO #6:

Given an application requiring active filters calculate, simulate and measure filter characteristic of a low-pass, high-pass, band-pass, and notch filter.

Part B- Oscillators

TCO#7:

Given an oscillator application, such as a tone generator, determine the operating parameters and calculate and measure the oscillator’s voltage, frequency and relative stability.

Part C-Filters and Oscillator Simulations

1.The circuit below is a two-pole high-pass Butterworth filter. The upper critical frequency should be 1.12kHz. Find the required value for R4 and the closed loop gain. Verify the circuit operation in Multisim. Make the necessary changes to the circuit and verify its operations. The Multisim file (ECT246_Week_6_Two_high_trouble.ms) can be found in Doc Sharing, week 7.

 

ECT 246 Week 7 iLab Lab 7 – Switching Transistors and

Optical Devices

Given a DC switching application such as driving a motor in one and

two directions use a SCR and a transistor and an H-bridge driver to

successfully perform the operation, calculate and measure the

operating voltages and currents.

Course Home Work aims to provide quality study notes and tutorials to the students of  ECT 246 Complete ilabs Week 1 To 7  in order to ace their studies.

Course Home Work – Best Home Work Tutorials

ECT 246 Complete ilabs Week 1 To 7

Course Home Work,   ECT 246 Complete ilabs Week 1 To 7   , Home Work Tutorials, Home Work Solutions, Home Work Essay, Home Work Questions.ACC 565 Wk 7 Assignment 3, ACC403 week 2 assignment, ACC565 Week 10, ACCT 212 (Financial Accounting),  ACCT 344 (Entire Course) – Devry, ACCT 344 Final Exam Latest 2014 – Devry,  ACCT 346 (Managerial Accounting), ACCT 346 Midterm Exam Updated DeVry, ACCT 504, ACCT 504 Week 8, ACCT 553, ART 101 Week 8, Ashford BUS 401, ASHFORD BUS 640, Ashford HIS 204, ASHFORD MAT 222 Week 3, BA 215 (Business Statistics), BA 215 All Assignments Week 1 -8 – Grantham, BA 225, BA 260, BA 265 (Business Law II), BA 265 (Business Law II) FINAL EXAM, BA 340 All Course Assignments, BA 340 Human Resource, BA 370 (Employment Law), BA 405 Multinational Management, BA 470 Week 3 – 5 – 6 – 7, BA 470 Entrepreneurship, BA350 Principles Of Finance, BIS 155 Final Exam – DeVry, BIS 220 Final Exam, BSOP 429, BSOP 434 Entire Course – Devry, BUS 303 Week 2, BUS 303 Week 3, BUS 303 Week 5, BUS 311 Business Law, BUS 330 Week 1, BUS 330 Week 3, BUS 330 Week 5, BUS 401 Week 4 DQ 1, BUS 401 Week 4 DQ 2, BUS 402 WEEK 4, BUS 405 (Principles of Investment), BUS 475, BUS 475 Final Exam 100 MCQS, BUS 475 Final Exam 600 MCQS, BUS 599 (STRAYER), BUS 599 Assignment, BUS 620 Week 4, BUS 640 Week 1, BUS499 Asignment 4, BUS508 Asignment 1, BUS499 Assignment 3.

ECT 246 Complete ilabs Week 1 To 7